HOW TO make your own PMC table

[ghamdan]

Instructions
A short HOW TO make your own PMC table


Tools:
1. Humax 5400 patched (ToH2.3 or higher)
2. PMC-editor ToH2.0 version or PMCTool

#> First step

- Detect the channel wont open with yours running PMCT and stay tuned
- Enter the ToH menu (green) EPG module and select PMCT
- Select with cursor the last page of your PMCT
- Open PMC-editor and load your running PMCT *( if you dont have one, you will need to create one with settings from your Humax reading and rewriting line by one creating nex PMCT)

#> Second step
- Press OK on your RCU and move cursor down to the end of the last PMCT line. When you reach last line next cursor move will
create a new RED line with new settings for this particular channel already entered. It will look like this:

ANT-ID ServID CA-ID ECM/Ident IdentExt AutoPid

[last line (eg.) ] IDENT 0 0500 00C4 0000 A+Vpid
[new line (eg.) ] 2 6 FFFF 0000 0000 A+Vpid

-Then press OK to confim your choice.If everything is going fine it will change coloure to WHITE.Thatt's OK but it still not
working.So you need to correct the ECM pid and Ident chosen by receiver:
Select new line and press OK it will RED again,(a blue box with some data appears on your right) press right cursor
to edit each field separately (all but selected will be white again). Change data according to appearing data on your right
(using cursor or numeric buttons). If you can not mannage with this data maybe next explanation will be helpful:

ANT-ID = Ident of satellite position in your channel list settings
IDENT is automatic selection
Numeric from 1 to 32 is exact ID selection
DEL deleting current input
ServID = Ident of current service
0 is automatic selection
CA-ID = Ident of possible encrypting system used by this service
0100 Seca
0500 Viaccess
0602 Irdeto
0604 **** (with Irdeto 2)
0604 also Zee TV
1702 PW Sat
1722 PW und MV Kabel (Betacrypt)
1762 ORF und PW Φstereich (Betacrypt)
1800 Nagra
ECM/Ident = ECM pid if you using exact selection or
Provider Ident if u r using automatic selection
IdentExt = Provider Ident if u r not using automatic selection and in ECM/Ident field is ECM pid
AutoPid = Audio or Video or both PID selection( some channels requires using of Vpid only but standard is both)

Inputing new data manualy in hex will be like this 0-9 (numeric buttons) A-F (colored buttons).Some times u can find much more
data numbered in a apearing box some of them are real and some are not (eg. TPS providers are using many false Idents and ECM
pids)


When you correct all needed data service will start running decrypted, but that is not all. If you want to do the correction
autoupdate for all services of that provider you need some more steps.That is chosing of IDENT in ANT-ID field, and moving
cursor right and corection of input ECM/Ident field (changing ECM data to Ident data) it become an autoupdate input.

Now you have correct input of a new PMC data but only till you turn off your receiver.So you need to transfer a new data to
PMC-editor tabel

#> Third step

-Transfer manualy all new data in to a PMCT using PMC-editor. In first column enter provider name (it is for orientation only)
You will also find a TO (time offset) column used to correct some real time showing problem.
ANT-ID 33 is used for IDENT (autoselection).
Save your new PMCT and send it to IRD.

* If you already don't have PMCT on your disk I recomend you transfer all data from your receiver in PMCT editor and save it.
(there is also some other way to that eg. by extract it from firmware and converting it, also creating it as so called
ECM.fix but it's a litlle bit complicated)
____________

[dema233]

الف شكر حبيبى