نفس المسج بيطلع
عند استعمال عدة برامج وكان اخرها الهايبرتيرمنال........
ويكون اخر سطر بالقراءه هو
turn off boot console early0
ثم يعيد نفس القراءات لان الرسيفر يحاول ان يعيد تشغيل نفسه
من خلال استعمال هذه البرامج جميعها يطلب الضغط بشكل موحد ومتتالي على ..."Shift" key. At the same time press "@" key and "Space" key..........والسبب لجعل الرسيفر يقف ويتجمد على كلمة boot...لكن الرسيفر يرفض ذالك ويستمر بمحاولة التشغيل وقراءة السوفتوير الذي عليه.......
باختصار ...نحتاج لجعل الرسيفر يتجمد على كلمة boot ...عندها ستحل المشكله
وهذا هو السج والقراءات من البرنامج
--------------------------------------------------------------------
-- Generic Primary Bootloader 88.88-8888, NI (10:14:27, Jul 6 2010)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 1 (expecting 2)
Poly10: 0x860756E3
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 000000000000000000000000000000 00
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
--------------------------------------------------------------------
-- Generic Primary Bootloader 88.88-8888, NI (10:14:27, Jul 6 2010)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 1 (expecting 2)
Poly10: 0x860756E3
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 000000000000000000000000000000 00
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 81964 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (AD76) Hynix SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 247534 uSec
re boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: Hynix 64MiB 3,3V 8-bit
init hdmi on i2c 1 bus.
Net: ip3902
Board Opts: EthOsc HDMI PAL
Splash: done
u-boot startup time so far: 1094 msec
Hit any key to stop autoboot-----: 0
Boot mode is :
Loading from 64MiB 3,3V 8-bit, offset 0x1020000
Automatic boot of image at addr 0x80800000 ...
## Booting image at 80800100 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 1618100 Bytes = 1.5 MB
Load Address: 80001000
Entry Point: 802bedb0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.6.24.7_nxp.STB236_NANDflash_ HDdecoding_128M_Huangpu.0425_a (nxpl
inux@bogon) (gcc version 4.2.1) #16 PREEMPT Sun Oct 16 16:52:23 CST 2011
console [early0] enabled
CPU revision is: 00019068 (MIPS 4KEc)
Determined physical RAM map:
memory: 02e8c000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 11916
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 11916
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 11823
Kernel command line: mtdparts=gen_nand:128k(B0),1M( B1),512k(Env),2M(K0),12M(F0),
512k(U0),3M(K1),33M(F1),3M(U1) ,7M(U2) ip3902.mac_address=00:13:8f:f9 :24:07 ip=19
2.168.0.52:192.168.0.220::::et h0 roo=/dev/mtdblock_rbbs7 ro rootfstype=cramfs
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
Synthesized clear page handler (26 instructions).
Synthesized copy page handler (46 instructions).
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU clock is 320 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 42592k/47664k available (2824k kernel code, 5072k reserved, 676k data, 1
28k init, 0k highmem)
SLUB: Genslabs=6, HWalign=16, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 64 bytes
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order:
0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
async_tx: api initialized (async)
io scheduler noop registered (default)
Serial: PNX8XXX driver $Revision: 1$
pnx8xxx-uart: ttyS0 at MMIO 0xb7e0b000 (irq = 11) is a PNX8XXX
loop: module loaded
PNX8335 AES: loaded
NXP ip3902 10/100 Ethernet platform driver irq 60 base b7e2f000
Linux video capture interface: v2.00
pwc: Philips webcam module version 10.0.13 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCV
C830/840.
pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10
and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and
VCS-UM100.
usbcore: registered new interface driver Philips webcam
Driver 'sd' needs updating - please use bus_type methods
NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
10 cmdlinepart partitions found on MTD device gen_nand
Creating 10 MTD partitions on "gen_nand":
0x00000000-0x00020000 : "B0"
0x00020000-0x00120000 : "B1"
0x00120000-0x001a0000 : "Env"
0x001a0000-0x003a0000 : "K0"
0x003a0000-0x00fa0000 : "F0"
0x00fa0000-0x01020000 : "U0"
0x01020000-0x01320000 : "K1"
0x01320000-0x03420000 : "F1"
0x03420000-0x03720000 : "U1"
0x03720000-0x03e20000 : "U2"
pnx833x-ehci pnx833x-ehci: PNX833x EHCI
pnx833x-ehci pnx833x-ehci: new USB bus registered, assigned bus number 1
pnx833x-ehci pnx833x-ehci: irq 40, io mem 0xb7e19000
pnx833x-ehci pnx833x-ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Stge driver...
usb 1-1: new high speed USB device using pnx833x-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serialUSB Serial supporregistered for GSM modem (1-port)
usbcomodems: v0.7.1
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
i2c-pnx0105: registered device at 0xb7e0d000
i2c-pnx0105: registered device at 0xb7e0e000
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
Bluetooth: Virtual HCI driver ver 1.2
nxp-aes driver : loaded
nxp-adma DMA driver irq 32 base b7e1c000
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
turn off boot console early0
كل الشكر لمن حاول تقديم المساعده...الاخ ابو المؤيد..ابو حاتم ..
رد: t600 2usb..بيعطي boot...رغم انه ياخذ جميع الاصدارات
.gif "Jo1Sat S (3)")
....او التاخير في الارسال والعوده للجهاز ان ارسل عن طريق احد مراكز الصيانه
.gif "Jo1Sat S (13)")
والمسافه التي سقطعها للتصليح رسيفره
رد مع اقتباس
المفضلات