هل يمكن اضافة سطر Mgcamd في oscam [الأرشيف]

Raed Saadeh

23-03-2013, 10:55 AM

اظن ما راح تضبط معك MGCAM بشكل كامل , الا باعدادات احترافية خاصة ..

اذا الـ OSCAM مربوط على مبرمجة مباشرة الامجيكامد ما بيفيد ,, انت بدك بدك تشغل سطر ام جي كامد على الاوسكام ؟؟ صحيح ؟؟ الامجيكامد عبارة عن نيوكامد ببورت واحد لجميع الباقات بامكانك عملها على الشكل :

تستطيع ربط mgcamd مع الاوسكام بتعديل عدة ملفات ,,

عدل ملف mg_cfg :

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 02 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 04 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 00 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

و newcamd.list :

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 127.0.0.1 10001 JO1SAT JO1SAT.COM 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

و oscam.conf :

[global]
nice = -1
logfile = /dev/null
clienttimeout = 5000
fallbacktimeout = 2500
clientmaxidle = 120
cachedelay = 120
bindwait = 120
resolvedelay = 30
serialreadertimeout = 1500
maxlogsize = 10
waitforcards = 1
preferlocalcards = 1
saveinithistory = 1
keepalive = 1

[monitor]
port = 988
aulow = 120
monlevel = 1

[newcamd]
port = 10001@09CD:000000
key = 0102030405060708091011121314
keepalive = 1
mgclient = 1

[webif]
httpport = 8888
httpuser =
httppwd =
httprefresh = 5
httphideidleclients = 0
httpallowed = 192.168.0.0 - 255.255.255.255
debug = 255

و oscam.user :

[account]
user = JO1SAT
pwd = JO1SAT.COM
group = 2
au = 1
caid = 09CD
ident = 09CD:000000

بالاعلى هذا يفيدك لربط mgcamd على OSCAM واخذ يوزر لباقة معينة وبالشرح بالاعلى لباقة سكاي ايطاليا ,,

بامكانك اضافة التالي للنيوكامد بامكانك تجربه على ام جي كامد لكن لا اظن انه ينفع بسهولة :

[reader]
label = VIA
protocol = newcamd
caid = 0500
ident = 0500:032830
key = 0102030405060708091011121314
device = 192.168.1.110,1180
user = JO1SAT
password = JO1SAT
group = 1
fallback = 1

جرب الملفات المرفقة ممكن تفيدك هي جاهزة لربط OSCAM و MGCAMD طبعا يبقى عليك اختيار الطريقة المناسبة اذا استطعت تفعيل سطور ام جي على اوسكام